Title Index
Recently Changed
Page Hierarchy
Incomplete
Tags
Subject: Printer settings for OKIDATA 320 and 321
-------------------------------------------------------------
Every printer model is different, so please refer to your printer operations
manual for instructions on how to print and change the settings.
Generally you'll use the MENU GROUP ITEM and SET buttons to make changes.
To get into MENU mode you might have to hold down the SHIFT button while you
press the MENU button.
To print out all settings at once, press MENU and PRINT.
The MENU button gets you into the menu mode.
The GROUP button prints the first line of each group
The ITEM button prints the next item within the current group.
The SET button prints (and sets) the current ITEM to a new setting.
--------------------------------------------------------------------
This was taken from an OKIDATA MICROLINE 320
--------------------------------------------------------------------
GROUP ITEM SET
--------------- ----------------- -----------------
Printer Control Emulation Mode ML (Microline) see notes 1.
Font Print Mode Utility
Font DRAFT Mode HSD
Font Pitch 10 CPI
Font Proportional Spacing No
Font Style Normal
Font Size Single
Symbol Sets Character Set Standard
Symbol Sets Language Set American
Symbol Sets Zero Character Slashed
Symbol Sets Code Page USA
Rear Feed Line Spacing 6 LPI
Rear Feed Form Tear-off 500ms
Rear Feed Skip Over Perforation No
Rear Feed Page Width 13.6 "
Rear Feed Page Length 11 "
Bottom Feed Line Spacing 6 LPI
Bottom Feed Form Tear-Off 500ms
Bottom Feed Skip Over Perforation No
Bottom Feed Page Width 13.6 "
Bottom Feed Page Length 11 "
Top Feed Line Spacing 6 LPI
Top Feed Bottom Margin Valid
Top Feed Page Width 13.6 "
Top Feed Page Length 11 "
Top Feed Wait Time 1 sec
Top Feed Page Length Control by Actual Page Length
Set-Up Graphics Bi-directional
Set-Up 7 or 8 Bits Graphics 7
Set-Up Receive Buffer Size 16K
Set_Up Paper Out Override Yes
Set-Up Print Registration 0
Set-Up 7 or 8 Bits Data Word 8
Set-Up Operator Panel Function Full Operation
Set-Up Reset Inhibit No
Set-Up Print Suppress Effective Yes
Set-Up Auto LF NO
Set-Up Print DEL Code No
Set-Up Time Out Print Valid
Set-Up Auto Select No
Set-Up Centering Position DEFAULT
Set-Up Decollator No
Set-Up CSF Type Wide
Parallel I/F I-Prime Buffer Print
Parallel I/F Pin 18 +5v
Serial I/F Parity None
Serial I/F Serial Data 7/8 Bits 8 Bits
Serial I/F Protocol Ready/Busy
Serial I/F Diagnostic Test No
Serial I/F Busy Line DTR
Serial I/F Baud Rate 9600 BPS
Serial I/F DSR Signal Invalid
Serial I/F DTR Signal Ready on Power Up
Serial I/F Busy Time 200 ms
--------------------------------------------------------------------
This was taken from an OKIDATA MICROLINE 321
--------------------------------------------------------------------
GROUP ITEM SET
--------------- ----------------- -----------------
General Control Emulation Mode IBM PPR see notes 1.
Font Print Mode Utility
Font Pitch 10 CPI
Font Proportional Spacing No
Font Style Normal
Font Size Single
General Control Graphics Bi-directional
General Control 7 or 8 Bit Graphics 7
General Control Max Receive Buffer Full
General Control Paper Out Override No
General Control Print Registration 0
General Control 7 or 8 Bit Data Word 8
General Control Operator Panel Functions Full Operation
General Control Reset Inhibit No
General Control Print Suppress Effective Yes
General Control Printable DEL code Yes
General Control Page Width 13.6"
Vertical Control Line Spacing 6 LPI
Vertical Control Form Tear-Off 500 ms
Vertical Control Skip Over Perforation No
Vertical Control Auto LF No
Vertical Control Page Length 11"
Vertical Control Cut Sheet Page Length 11"
Symbol Sets Character Set Standard
Symbol Sets Language Set American
Serial I/F Parity None
Serial I/F Serial Data 7 or 8 Bits 8
Serial I/F Protocol Ready/Busy
Serial I/F Diagnostic Test No
Serial I/F Busy Line DTR
Serial I/F Baud Rate 9600 BPS
Serial I/F DSR Signal Invalid
Serial I/F DTR Signal Ready on Power Up
Serial I/F Busy Time 200 ms
---------------------------------------------------------------------------
notes:
1. Emulation mode. ML, EPSON, IBM PPR
The emulation mode must match the type of codes used in the printer record
for this printer listed in S/M task 22. "System printers"
Fields: 07. Cmp codes and 08. Nor codes contain the printer codes used to
make the printer print normal or compressed fonts.
Cmp=015,000,000,000 and Nor=018,000,000,000 are IBM PPR emulation.
Cmp=029,000,000,000 and Nor=030,000,000,000 are ML or EPSON emulation.
For a list of possible compress and normal codes see S/M task
32/9. Printer model master and do a tab search on field 01. Model ID for
"OKI". Examples of IBMPPR, ML and EPSON emulation codes are givien.
